Fibershield-P - Watermist

The Premium textile fire protection closure to match highest demands and to achieve large dimensions

Protection target

	Insulation with watermist in case of fire
Classification	EI 90 EI 180
Fabric	Protex 1100 B1 Protex 1100.1 A2
Test reports	UU IV/00-39-1 UB III/B-02-008-1 08/32309876 2011-Efectis-R0495
Water irrigation

 

Description of the Fibershield-P system

• Approval classification E90, 10.000 cycles
• Scope of approval 1000 mm x 2000 mm - 10.000 mm x 7.600 mm
• Made out of one piece up to a width of 30 m and for a large drop length (see table)
• Highest variability for the construction and the design
  
• Drive system "Gravigen" as a standard - that is closing without auxiliary power, no fire-rated cables necessary
• High number of cycles of the motor of 10.000 cycles
• Only one drive system is necessary - therefore a reduced effort to the installation
• Different protection targets E, EW, EI (with water) by using different types of fabrics
• Large widths as well as the self levelling bottom bar (for the standard casing)
• The safety edge in combination with the self levelling bottom bar is possible as an option
  
• Continuing lateral fixing of the fabric by using the side guides with steel rod for large drop length, high pressures, high tightness and gentle closing
• Warping free bottom bars even in case of temperature influence
• Large fire protection closures min. class C1 regarding DIN EN 13501-2
  

Fixed bearing

Floating bearing

Range of casings

Standard fixed bearing		Standard floating bearing		Range of special constructions

Bottom bars

Standard with small widths

Type 4,6		heavy, Type 9.6		small, Type 5,61

Standard with large widths

Type 3,84 F self levelling bottom bar without safety edge		Type 3,84 FK self levelling - optional with safety edge		self levelling bottom bar without safety edge, under ceiling

Range of side guides

Continuous fabric clamping due to rod guiding for high pressures and high tightness

Type Drop  length Surface 80 E ≤ 3,5 m ≤ 18 m2 105 E  ≤ 6 m ≤ 50 m2 105 V  ≤ 6 m ≤ 70 m2 160 E  ≤ 9 m ≤ 120 m2

 

 

Type 105 E  installation to the wall		Type 105 E  installation in the embrasure		Type 105 E installation in the niche		Type 105 V  installation to the wall

Type 105 V  installation in the embrasure		Type 105 V  installation in the niche		Type 80 E installation to the wall		Type 80 E installation in the embrasure

Type 80 E installation in the niche		Type 140 E installation to the wall		Type 140 E installation in the embrasure		Type 140 E installation in the niche

Alternatives for the installation

Installation of the casing to the wall, front site run		Installation of the casing to the wall, rear site run		Installation of the casing to the wall, false ceiling is attached to the casing on one side, front site run		Installation of the casing to the wall, false ceiling is attached to the casing on one side, rear site run

Installation of the casing directly to the ceiling		Installation of the casing directly to the ceiling, false ceiling is attached to the casing on both sides		Installation of the casing to the ceiling by using hangers		Installation of the casing to the ceiling by using hangers, false ceiling is attached to the casing on both sides

Control units for fire protection closures

Control units for single closures:

• without hold-open time in case of power failure
• with up to 10 min hold-open time in case of power failure
• with over 10 min hold-open time in case of power failure

Control units for multiple closures:

• without hold-open time in case of power failure
• with up to 10 min hold-open time in case of power failure
• with over 10 min hold-open time in case of power failure